#GNU mailman - installation Manual About this document... About this document... Previous Page Up one Level Next Page GNU Mailman - Installation Manual __________________________________________________________________ GNU Mailman - Installation Manual Barry Warsaw barry (at) list dot org Release 2.1 February 26, 2019 Front Matter Abstract: This document describes how to install GNU Mailman on a POSIX-based system such as Unix, MacOSX, or GNU/Linux. It will cover basic installation instructions, as well as guidelines for integrating Mailman with your web and mail servers. The GNU Mailman website is at http://www.list.org 1 Installation Requirements Please note that the information on this page may be out of date. Check for the latest installation information on the Mailman wiki. GNU Mailman works on most POSIX-based systems such as Unix, MacOSX, or GNU/Linux. It does not currently work on Windows. You must have a mail server that you can send messages to, and a web server that supports the CGI/1.1 API. Apache makes a fine choice for web server, and mail servers such as Postfix, Exim, Sendmail, and qmail should work just fine. To install Mailman from source, you will need an ANSI C compiler to build Mailman's security wrappers. The GNU C compiler gcc works well. You must have the Python interpreter installed somewhere on your system. As of this writing, Python 2.4.4 is recommended, but see the wiki page above for the latest information. 2 Set up your system Before installing Mailman, you need to prepare your system by adding certain users and groups. You will need to have root privileges to perform the steps in this section. 2.1 Add the group and user Mailman requires a unique user and group name which will own its files, and under which its processes will run. Mailman's basic security is based on group ownership permissions, so it's important to get this step right^1. Typically, you will add a new user and a new group, both called mailman. The mailman user must be a member of the mailman group. Mailman will be installed under the mailman user and group, with the set-group-id (setgid) bit enabled. If these names are already in use, you can choose different user and group names, as long as you remember these when you run configure. If you choose a different unique user name, you will have to specify this with configure's --with-username option, and if you choose a different group name, you will have to specify this with configure's --with-groupname option. On Linux systems, you can use the following commands to create these accounts. Check your system's manual pages for details: % groupadd mailman % useradd -c"GNU Mailman" -s /no/shell -d /no/home -g mailman mailman 2.2 Create the installation directory Typically, Mailman is installed into a single directory, which includes both the Mailman source code and the run-time list and archive data. It is possible to split the static program files from the variable data files and install them in separate directories. This section will describe the available options. The default is to install all of Mailman to /usr/local/mailman^2. You can change this base installation directory (referred to here as $prefix) by specifying the directory with the --prefix configure option. If you're upgrading from a previous version of Mailman, you may want to use the --prefix option unless you move your mailing lists. Warning: You cannot install Mailman on a filesystem that is mounted with the nosuid option. This will break Mailman, which relies on setgid programs for its security. If this describes your environment, simply install Mailman in a location that allows setgid programs. Make sure the installation directory is set to group mailman (or whatever you're going to specify with --with-groupname) and has the setgid bit set^3. You probably also want to guarantee that this directory is readable and executable by everyone. For example, these shell commands will accomplish this: % cd $prefix % chgrp mailman . % chmod a+rx,g+ws . Warning: The installation directory, $prefix, cannot be the same directory that the source tarball has been unpacked to and in which you run configure, but it can, if you wish, be a subdirectory, e.g., $prefix/src. You are now ready to configure and install the Mailman software. 3 Build and install Mailman 3.1 Run configure Before you can install Mailman, you must run configure to set various installation options your system might need. Note: Take special note of the --with-mail-gid and --with-cgi-gid options below. You will probably need to use these. You should not be root while performing the steps in this section. Do them under your own login, or whatever account you typically use to install software. You do not need to do these steps as user mailman, but you could. However, make sure that the login used is a member of the mailman group as that that group has write permissions to the $prefix directory made in the previous step. You must also have permission to create a setgid file in the file system where it resides (NFS and other mounts can be configured to inhibit setgid settings). If you've installed other GNU software, you should be familiar with the configure script. Usually you can just cd to the directory you unpacked the Mailman source tarball into, and run configure with no arguments: % cd mailman- % ./configure % make install The following options allow you to customize your Mailman installation. --prefix=dir Standard GNU configure option which changes the base directory that Mailman is installed into. By default $prefix is /usr/local/mailman. This directory must already exist, and be set up as described in 2.2. --exec-prefix=dir Standard GNU configure option which lets you specify a different installation directory for architecture dependent binaries. --with-var-prefix=dir Store mutable data under dir instead of under the $prefix or $exec_prefix. Examples of such data include the list archives and list settings database. --with-python=/path/to/python Specify an alternative Python interpreter to use for the wrapper programs. The default is to use the interpreter found first on your shell's $PATH. --with-username=username-or-uid Specify a different username than mailman. The value of this option can be an integer user id or a user name. Be sure your $prefix directory is owned by this user. --with-groupname=groupname-or-gid Specify a different groupname than mailman. The value of this option can be an integer group id or a group name. Be sure your $prefix directory is group-owned by this group. --with-mail-gid=group-or-groups Specify an alternative group for running scripts via the mail wrapper. group-or-groups can be a list of one or more integer group ids or symbolic group names. The first value in the list that resolves to an existing group is used. By default, the value is the list mailman, other, mail, and daemon. Note: This is highly system dependent and you must get this right, because the group id is compiled into the mail wrapper program for added security. On systems using sendmail, the sendmail.cf configuration file designates the group id of sendmail processes using the DefaultUser option. (If commented out, it still may be indicating the default...) Check your mail server's documentation and configuration files to find the right value for this switch. --with-cgi-gid=group-or-groups Specify an alternative group for running scripts via the CGI wrapper. group-or-groups can be a list of one or more integer group ids or symbolic group names. The first value in the list that resolves to an existing group is used. By default, the value is the the list www, www-data, and nobody. Note: The proper value for this is dependent on your web server configuration. You must get this right, because the group id is compiled into the CGI wrapper program for added security, and no Mailman CGI scripts will run if this is incorrect. If you're using Apache, check the values for the Group option in your httpd.conf file. --with-cgi-ext=extension Specify an extension for cgi-bin programs. The CGI wrappers placed in $prefix/cgi-bin will have this extension (some web servers require an extension). extension must include the leading dot. --with-mailhost=hostname Specify the fully qualified host name part for outgoing email. After the installation is complete, this value can be overriden in $prefix/Mailman/mm_cfg.py. --with-urlhost=hostname Specify the fully qualified host name part of urls. After the installation is complete, this value can be overriden in $prefix/Mailman/mm_cfg.py. --with-gcc=no Don't use gcc, even if it is found. In this case, cc must be found on your $PATH. 3.2 Make and install Once you've run configure, you can simply run make, then make install to build and install Mailman. 4 Check your installation After you've run make install, you should check that your installation has all the correct permissions and group ownerships by running the check_perms script. First change to the installation (i.e. $prefix) directory, then run the bin/check_perms program. Don't try to run bin/check_perms from the source directory; it will only run from the installation directory. If this reports no problems, then it's very likely that your installation is set up correctly. If it reports problems, then you can either fix them manually, re-run the installation, or use bin/check_perms to fix the problems (probably the easiest solution): * You need to become the user that did the installation, and that owns all the files in $prefix, or root. * Run bin/check_perms -f * Repeat previous step until no more errors are reported! Warning: If you're running Mailman on a shared multiuser system, and you have mailing lists with private archives, you may want to hide the private archive directory from other users on your system. In that case, you should drop the other execute permission (o-x) from the archives/private directory. However, the web server process must be able to follow the symbolic link in public directory, otherwise your public Pipermail archives will not work. To set this up, become root and run the following commands: # cd /archives # chown private # chmod o-x private You need to know what user your web server runs as. It may be www, apache, httpd or nobody, depending on your server's configuration. 5 Set up your web server Congratulations! You've installed the Mailman software. To get everything running you need to hook Mailman up to both your web server and your mail system. If you plan on running your mail and web servers on different machines, sharing Mailman installations via NFS, be sure that the clocks on those two machines are synchronized closely. You might take a look at the file Mailman/LockFile.py; the constant CLOCK_SLOP helps the locking mechanism compensate for clock skew in this type of environment. This section describes some of the things you need to do to connect Mailman's web interface to your web server. The instructions here are somewhat geared toward the Apache web server, so you should consult your web server documentation for details. You must configure your web server to enable CGI script permission in the $prefix/cgi-bin to run CGI scripts. The line you should add might look something like the following, with the real absolute directory substituted for $prefix, of course: Exec /mailman/* $prefix/cgi-bin/* or: ScriptAlias /mailman/ $prefix/cgi-bin/ Warning: You want to be very sure that the user id under which your CGI scripts run is not in the mailman group you created above, otherwise private archives will be accessible to anyone. Copy the Mailman, Python, and GNU logos to a location accessible to your web server. E.g. with Apache, you've usually got an icons directory that you can drop the images into. For example: % cp $prefix/icons/*.{jpg,png} /path/to/apache/icons You then want to add a line to your $prefix/Mailman/mm_cfg.py file which sets the base URL for the logos. For example: IMAGE_LOGOS = '/images/' The default value for IMAGE_LOGOS is /icons/. Read the comment in Defaults.py.in for details. Configure your web server to point to the Pipermail public mailing list archives. For example, in Apache: Alias /pipermail/ $varprefix/archives/public/ where $varprefix is usually $prefix unless you've used the --with-var-prefix option to configure. Also be sure to configure your web server to follow symbolic links in this directory, otherwise public Pipermail archives won't be accessible. For Apache users, consult the FollowSymLinks option. If you're going to be supporting internationalized public archives, you will probably want to turn off any default charset directive for the Pipermail directory, otherwise your multilingual archive pages won't show up correctly. Here's an example for Apache, based on the standard installation directories: AddDefaultCharset Off Also, you may need to specifically allow access to Mailman's directories. For example, in Apache, the above Directory block may need something like Require all granted or Order allow,deny Allow from all depending on the Apache version and similarly for the $prefix/cgi-bin/ directory. Now restart your web server. 6 Set up your mail server This section describes some of the things you need to do to connect Mailman's email interface to your mail server. The instructions here are different for each mail server; if your mail server is not described in the following subsections, try to generalize from the existing documentation, and consider contributing documentation updates to the Mailman developers. Under rare circumstances or due to mis-configuration, mail to the owner(s) of the 'mailman' site-list (see section 8) can bounce. In order to prevent a mail loop this mail is sent with envelope from mailman-loop which is normally aliased as mailman-loop: $varprefix/data/owner-bounces.mbox but which can be aliased to any, always deliverable, local address or file. If you are using the Postfix MTA integrated as described in section 6.1, this alias will be generated automatically. In all other cases, you should install this alias along with your normal system aliases. 6.1 Using the Postfix mail server Mailman should work pretty much out of the box with a standard Postfix installation. It has been tested with various Postfix versions up to and including Postfix 2.11.3 (as of April 2016). In order to support Mailman's optional VERP delivery, you will want to disable luser_relay (the default) and you will want to set recipient_delimiter for extended address semantics. You should comment out any luser_relay value in your main.cf and just go with the defaults. Also, add this to your main.cf file: recipient_delimiter = + Using "+" as the delimiter works well with the default values for VERP_FORMAT and VERP_REGEXP in Defaults.py. When attempting to deliver a message to a non-existent local address, Postfix may return a 450 error code. Since this is a transient error code, Mailman will continue to attempt to deliver the message for DELIVERY_RETRY_PERIOD - 5 days by default. You might want to set Postfix up so that it returns permanent error codes for non-existent local users by adding the following to your main.cf file: unknown_local_recipient_reject_code = 550 Finally, if you are using Postfix-style virtual domains, read the section on virtual domain support below. 6.1.1 Integrating Postfix and Mailman You can integrate Postfix and Mailman such that when new lists are created, or lists are removed, Postfix's alias database will be automatically updated. The following are the steps you need to take to make this work. In the description below, we assume that you've installed Mailman in the default location, i.e. /usr/local/mailman. If that's not the case, adjust the instructions according to your use of configure's --prefix and --with-var-prefix options. Note: If you are using virtual domains and you want Mailman to honor your virtual domains, read the 6.1 section below first! Then come back here and do these steps. * Add this to the bottom of the $prefix/Mailman/mm_cfg.py file: MTA = 'Postfix' The MTA variable names a module in the Mailman/MTA directory which contains the mail server-specific functions to be executed when a list is created or removed. * Look at the Defaults.py file for the variables POSTFIX_ALIAS_CMD and POSTFIX_MAP_CMD command. Make sure these point to your postalias and postmap programs respectively. Remember that if you need to make changes, do it in mm_cfg.py. * Run the bin/genaliases script to initialize your aliases file. % cd /usr/local/mailman % bin/genaliases Make sure that the owner of the data/aliases and data/aliases.db file is mailman, that the group owner for those files is mailman, or whatever user and group you used in the configure command, and that both files are group writable: % su % chown mailman:mailman data/aliases* % chmod g+w data/aliases* * Hack your Postfix's main.cf file to include the following path in your alias_maps variable: /usr/local/mailman/data/aliases Note that there should be no trailing .db. Do not include this in your alias_database variable. This is because you do not want Postfix's newaliases command to modify Mailman's aliases.db file, but you do want Postfix to consult aliases.db when looking for local addresses. You probably want to use a hash: style database for this entry. Here's an example: alias_maps = hash:/etc/postfix/aliases, hash:/usr/local/mailman/data/aliases * When you configure Mailman, use the --with-mail-gid=mailman switch; this will be the default if you configured Mailman after adding the mailman owner. Because the owner of the aliases.db file is mailman, Postfix will execute Mailman's wrapper program as uid and gid mailman. That's it! One caveat: when you add or remove a list, the aliases.db file will updated, but it will not automatically run postfix reload. This is because you need to be root to run this and suid-root scripts are not secure. The only effect of this is that it will take about a minute for Postfix to notice the change to the aliases.db file and update its tables. 6.1.2 Virtual domains Note: This section describes how to integrate Mailman with Postfix for automatic generation of Postfix virtual_alias_maps for Mailman list addresses. Mailman's support of virtual domains is limited in that list names must be globally unique within a single Mailman instance, i.e., two lists may not have the same name even if they are in different domains. Postfix 2.0 supports ``virtual alias domains'', essentially what used to be called ``Postfix-style virtual domains'' in earlier Postfix versions. To make virtual alias domains work with Mailman, you need to do some setup in both Postfix and Mailman. Mailman will write all virtual alias mappings to a file called, by default, /usr/local/mailman/data/virtual-mailman. It will also use postmap to create the virtual-mailman.db file that Postfix will actually use. First, you need to set up the Postfix virtual alias domains as described in the Postfix documentation (see Postfix's virtual(5) manpage). Note that it's your responsibility to include the virtual-alias.domain anything line as described manpage (in recent Postfix this is not required if the domain is included in virtual_alias_domains in main.cf); Mailman will not include this line in virtual-mailman. You are highly encouraged to make sure your virtual alias domains are working properly before integrating with Mailman. Next, add a path to Postfix's virtual_alias_maps variable, pointing to the virtual-mailman file, e.g.: virtual_alias_maps = , hash:/usr/local/mailman/data/virtual-mailman assuming you've installed Mailman in the default location. If you're using an older version of Postfix which doesn't have the virtual_alias_maps variable, use the virtual_maps variable instead. The default mappings in virtual-mailman map list addresses in virtual domains to unqualified local names as in: mylist@dom.ain mylist mylist-request@dom.ain mylist-request # and so on... In some Postfix configurations it may be necessary to qualify those local names as for example: mylist@dom.ain mylist@localhost mylist-request@dom.ain mylist-request@localhost # and so on... If this is the case, you can include VIRTUAL_MAILMAN_LOCAL_DOMAIN = 'localhost' or whatever qualification is needed in mm_cfg.py. Next, in your mm_cfg.py file, you will want to set the variable POSTFIX_STYLE_VIRTUAL_DOMAINS to the list of virtual domains that Mailman should update. This may not be all of the virtual alias domains that your Postfix installation supports! The values in this list will be matched against the host_name attribute of mailing lists objects, and must be an exact match. Here's an example. Note that this example describes an unusual configuration. A more usual configuration is described next. Say that Postfix is configured to handle the virtual domains dom1.ain, dom2.ain, and dom3.ain, and further that in your main.cf file you've got the following settings: myhostname = mail.dom1.ain mydomain = dom1.ain mydestination = $myhostname, localhost.$mydomain virtual_alias_maps = hash:/some/path/to/virtual-dom1, hash:/some/path/to/virtual-dom2, hash:/some/path/to/virtual-dom2 If in your virtual-dom1 file, you've got the following lines: dom1.ain IGNORE @dom1.ain @mail.dom1.ain this tells Postfix to deliver anything addressed to dom1.ain to the same mailbox at mail.dom1.com, its default destination. In this case you would not include dom1.ain in POSTFIX_STYLE_VIRTUAL_DOMAINS because otherwise Mailman will write entries for mailing lists in the dom1.ain domain as mylist@dom1.ain mylist mylist-request@dom1.ain mylist-request # and so on... The more specific entries trump your more general entries, thus breaking the delivery of any dom1.ain mailing list. However, you would include dom2.ain and dom3.ain in mm_cfg.py: POSTFIX_STYLE_VIRTUAL_DOMAINS = ['dom2.ain', 'dom3.ain'] Now, any list that Mailman creates in either of those two domains, will have the correct entries written to /usr/local/mailman/data/virtual-mailman. In a more usual configuration, dom1.ain would not be a virtual domain at all as in the following: myhostname = mail.dom1.ain mydomain = dom1.ain mydestination = $myhostname, $mydomain localhost.$mydomain virtual_alias_maps = hash:/some/path/to/virtual-dom2, hash:/some/path/to/virtual-dom2 In this case too, you would include dom2.ain and dom3.ain in mm_cfg.py: POSTFIX_STYLE_VIRTUAL_DOMAINS = ['dom2.ain', 'dom3.ain'] As in the previous section with the data/aliases* files, you want to make sure that both data/virtual-mailman and data/virtual-mailman.db are user and group owned by mailman. 6.1.3 An alternative approach Fil fil@rezo.net has an alternative approach based on virtual maps and regular expressions, as described at: * (French) http://listes.rezo.net/comment.php * (English) http://listes.rezo.net/how.php This is a good (and simpler) alternative if you don't mind exposing an additional hostname in the domain part of the addresses people will use to contact your list. I.e. if people should use mylist@lists.dom.ain instead of mylist@dom.ain. 6.2 Using the Exim mail server Note: This section is derived from Nigel Metheringham's ``HOWTO - Using Exim and Mailman together'', which covers Mailman 2.0.x and Exim 3. It has been updated to cover Mailman 2.1 and Exim 4. The updated document is here: http://www.exim.org/howto/mailman21.html and is recommended over the information in the subsections below if you are using Exim 4. There is no Mailman configuration needed other than the standard options detailed in the Mailman install documentation. The Exim configuration is transparent to Mailman. The user and group settings for Mailman must match those in the config fragments given below. 6.2.1 Exim configuration The Exim configuration is built so that a list created within Mailman automatically appears to Exim without the need for defining any additional aliases. The drawback of this configuration is that it will work poorly on systems supporting lists in several different mail domains. While Mailman handles virtual domains, it does not yet support having two distinct lists with the same name in different virtual domains, using the same Mailman installation. This will eventually change. (But see below for a variation on this scheme that should accommodate virtual domains better.) The configuration file excerpts below are for use in an already functional Exim configuration, which accepts mail for the domain in which the list resides. If this domain is separate from the others handled by your Exim configuration, then you'll need to: * add the list domain, ``my.list.domain'' to local_domains * add a ``domains=my.list.domain'' option to the director (router) for the list * (optional) exclude that domain from your other directors (routers) Note: The instructions in this document should work with either Exim 3 or Exim 4. In Exim 3, you must have a local_domains configuration setting; in Exim 4, you most likely have a local_domains domainlist. If you don't, you probably know what you're doing and can adjust accordingly. Similarly, in Exim 4 the concept of ``directors'' has disappeared - there are only routers now. So if you're using Exim 4, whenever this document says ``director'', read ``router''. Whether you are using Exim 3 or Exim 4, you will need to add some macros to the main section of your Exim config file. You will also need to define one new transport. With Exim 3, you'll need to add a new director; with Exim 4, a new router plays the same role. Finally, the configuration supplied here should allow co-habiting Mailman 2.0 and 2.1 installations, with the proviso that you'll probably want to use mm21 in place of mailman - e.g., MM21_HOME, mm21_transport, etc. 6.2.2 Main configuration settings First, you need to add some macros to the top of your Exim config file. These just make the director (router) and transport below a bit cleaner. Obviously, you'll need to edit these based on how you configured and installed Mailman. # Home dir for your Mailman installation -- aka Mailman's prefix # directory. MAILMAN_HOME=/usr/local/mailman MAILMAN_WRAP=MAILMAN_HOME/mail/mailman # User and group for Mailman, should match your --with-mail-gid # switch to Mailman's configure script. MAILMAN_USER=mailman MAILMAN_GROUP=mailman 6.2.3 Transport for Exim 3 Add this to the transports section of your Exim config file, i.e. somewhere between the first and second ``end'' line: mailman_transport: driver = pipe command = MAILMAN_WRAP \ '${if def:local_part_suffix \ {${sg{$local_part_suffix}{-(\\w+)(\\+.*)?}{\$1}}} \ {post}}' \ $local_part current_directory = MAILMAN_HOME home_directory = MAILMAN_HOME user = MAILMAN_USER group = MAILMAN_GROUP 6.2.4 Director for Exim 3 If you're using Exim 3, you'll need to add the following director to your config file (directors go between the second and third ``end'' lines). Also, don't forget that order matters - e.g. you can make Mailman lists take precedence over system aliases by putting this director in front of your aliasfile director, or vice-versa. # Handle all addresses related to a list 'foo': the posting address. # Automatically detects list existence by looking # for lists/$local_part/config.pck under MAILMAN_HOME. mailman_director: driver = smartuser require_files = MAILMAN_HOME/lists/$local_part/config.pck suffix_optional suffix = -bounces : -bounces+* : \ -confirm+* : -join : -leave : \ -owner : -request : -admin transport = mailman_transport 6.2.5 Router for Exim 4 In Exim 4, there's no such thing as directors - you need to add a new router instead. Also, the canonical order of the configuration file was changed so routers come before transports, so the router for Exim 4 comes first here. Put this router somewhere after the ``begin routers'' line of your config file, and remember that order matters. mailman_router: driver = accept require_files = MAILMAN_HOME/lists/$local_part/config.pck local_part_suffix_optional local_part_suffix = -admin : -bounces : -bounces+* : \ -confirm : -confirm+* : \ -join : -leave : \ -owner : -request : \ -subscribe : -unsubscribe transport = mailman_transport 6.2.6 Transports for Exim 4 The transport for Exim 4 is the same as for Exim 3 (see 6.2; just copy the transport given above to somewhere under the ``begin transports'' line of your Exim config file. 6.2.7 Additional notes Exim should be configured to allow reasonable volume - e.g. don't set max_recipients down to a silly value - and with normal degrees of security - specifically, be sure to allow relaying from 127.0.0.1, but pretty much nothing else. Parallel deliveries and other tweaks can also be used if you like; experiment with your setup to see what works. Delay warning messages should be switched off or configured to only happen for non-list mail, unless you like receiving tons of mail when some random host is down. 6.2.8 Problems * Mailman will send as many MAIL FROM/RCPT TO as it needs. It may result in more than 10 or 100 messages sent in one connection, which will exceed the default value of Exim's smtp_accept_queue_per_connection value. This is bad because it will cause Exim to switch into queue mode and severely delay delivery of your list messages. The way to fix this is to set Mailman's SMTP_MAX_SESSIONS_PER_CONNECTION (in $prefix/Mailman/mm_cfg.py) to a smaller value than Exim's smtp_accept_queue_per_connection. * Mailman should ignore Exim delay warning messages, even though Exim should never send this to list messages. Mailman 2.1's general bounce detection and VERP support should greatly improve the bounce detector's hit rates. * List existence is determined by the existence of a config.pck file for a list. If you delete lists by foul means, be aware of this. * If you are getting Exim or Mailman complaining about user ids when you send mail to a list, check that the MAILMAN_USER and MAILMAN_GROUP match those of Mailman itself (i.e. what were used in the configure script). Also make sure you do not have aliases in the main alias file for the list. 6.2.9 Receiver Verification Exim's receiver verification feature is very useful - it lets Exim reject unrouteable addresses at SMTP time. However, this is most useful for externally-originating mail that is addressed to mail in one of your local domains. For Mailman list traffic, mail originates on your server, and is addressed to random external domains that are not under your control. Furthermore, each message is addressed to many recipients - up to 500 if you use Mailman's default configuration and don't tweak SMTP_MAX_RCPTS. Doing receiver verification on Mailman list traffic is a recipe for trouble. In particular, Exim will attempt to route every recipient addresses in outgoing Mailman list posts. Even though this requires nothing more than a few DNS lookups for each address, it can still introduce significant delays. Therefore, you should disable recipient verification for Mailman traffic. Under Exim 3, put this in your main configuration section: receiver_verify_hosts = !127.0.0.1 Under Exim 4, this is probably already taken care of for you by the default recipient verification ACL statement (in the RCPT TO ACL): accept domains = +local_domains endpass message = unknown user verify = recipient which only does recipient verification on addresses in your domain. (That's not exactly the same as doing recipient verification only on messages coming from non-127.0.0.1 hosts, but it should do the trick for Mailman.) 6.2.10 SMTP Callback Exim's SMTP callback feature is an even more powerful way to detect bogus sender addresses than normal sender verification. Unfortunately, lots of servers send bounce messages with a bogus address in the header, and there are plenty that send bounces with bogus envelope senders (even though they're supposed to just use an empty envelope sender for bounces). In order to ensure that Mailman can disable/remove bouncing addresses, you generally want to receive bounces for Mailman lists, even if those bounces are themselves not bounceable. Thus, you might want to disable SMTP callback on bounce messages. With Exim 4, you can accomplish this using something like the following in your RCPT TO ACL: # Accept bounces to lists even if callbacks or other checks would fail warn message = X-WhitelistedRCPT-nohdrfromcallback: Yes condition = \ ${if and {{match{$local_part}{(.*)-bounces\+.*}} \ {exists {MAILMAN_HOME/lists/$1/config.pck}}} \ {yes}{no}} accept condition = \ ${if and {{match{$local_part}{(.*)-bounces\+.*}} \ {exists {MAILMAN_HOME/lists/$1/config.pck}}} \ {yes}{no}} # Now, check sender address with SMTP callback. deny !verify = sender/callout=90s If you also do SMTP callbacks on header addresses, you'll want something like this in your DATA ACL: deny !condition = $header_X-WhitelistedRCPT-nohdrfromcallback: !verify = header_sender/callout=90s 6.2.11 Doing VERP with Exim and Mailman VERP will send one email, with a separate envelope sender (return path), for each of your subscribers - read the information in $prefix/Mailman/Defaults.py for the options that start with VERP. In a nutshell, all you need to do to enable VERP with Exim is to add these lines to $prefix/Mailman/mm_cfg.py: VERP_PASSWORD_REMINDERS = Yes VERP_PERSONALIZED_DELIVERIES = Yes VERP_DELIVERY_INTERVAL = Yes VERP_CONFIRMATIONS = Yes (The director (router) above is smart enough to deal with VERP bounces.) 6.2.12 Virtual Domains One approach to handling virtual domains is to use a separate Mailman installation for each virtual domain. Currently, this is the only way to have lists with the same name in different virtual domains handled by the same machine. In this case, the MAILMAN_HOME and MAILMAN_WRAP macros are useless - you can remove them. Change your director (router) to something like this: require_files = /virtual/${domain}/mailman/lists/${lc:$local_part}/config.pck and change your transport like this: command = /virtual/${domain}/mailman/mail/mailman \ ${if def:local_part_suffix \ {${sg{$local_part_suffix}{-(\\w+)(\\+.*)?}{\$1}}} {post}} \ $local_part current_directory = /virtual/${domain}/mailman home_directory = /virtual/${domain}/mailman 6.2.13 List Verification This is how a set of address tests for the Exim lists look on a working system. The list in question is quixote-users@mems-exchange.org, and these commands were run on the mems-exchange.org mail server ("% " indicates the Unix shell prompt): % exim -bt quixote-users quixote-users@mems-exchange.org router = mailman_main_router, transport = mailman_transport % exim -bt quixote-users-request quixote-users-request@mems-exchange.org router = mailman_router, transport = mailman_transport % exim -bt quixote-users-bounces quixote-users-bounces@mems-exchange.org router = mailman_router, transport = mailman_transport % exim -bt quixote-users-bounces+luser=example.com quixote-users-bounces+luser=example.com@mems-exchange.org router = mailman_router, transport = mailman_transport If your exim -bt output looks something like this, that's a start: at least it means Exim will pass the right messages to the right Mailman commands. It by no means guarantees that your Exim/Mailman installation is functioning perfectly, though! 6.2.14 Document History Originally written by Nigel Metheringham postmaster@exim.org. Updated by Marc Merlin marc_soft@merlins.org for Mailman 2.1, Exim 4. Overhauled/reformatted/clarified/simplified by Greg Ward gward@python.net. 6.3 Using the Sendmail mail server Warning: You may be tempted to set the DELIVERY_MODULE configuration variable in mm_cfg.py to 'Sendmail' when using the Sendmail mail server. Don't. The Sendmail.py module is misnamed - it's really a command line based message handoff scheme as opposed to the SMTP scheme used in SMTPDirect.py (the default). Sendmail.py has known security holes and is provided as a proof-of-concept only^4. If you are having problems using SMTPDirect.py fix those instead of using Sendmail.py, or you may open your system up to security exploits. 6.3.1 Sendmail ``smrsh'' compatibility Many newer versions of Sendmail come with a restricted execution utility called ``smrsh'', which limits the executables that Sendmail will allow to be used as mail programs. You need to explicitly allow Mailman's wrapper program to be used with smrsh or Mailman will not work. If mail is not getting delivered to Mailman's wrapper program and you're getting an ``operating system error'' in your mail syslog, this could be your problem. One good way of enabling this is: * Find out where your Sendmail executes its smrsh wrapper % grep smrsh /etc/mail/sendmail.cf * Figure out where smrsh expects symlinks for allowable mail programs. At the very beginning of the following output you will see a full path to some directory, e.g. /var/adm/sm.bin or similar: % strings $path_to_smrsh | less * cd into /var/adm/sm.bin, or where ever it happens to reside on your system - alternatives include /etc/smrsh, /var/smrsh and /usr/local/smrsh. % cd /var/adm/sm.bin * Create a symbolic link to Mailman's wrapper program: % ln -s /usr/local/mailman/mail/mailman mailman 6.3.2 Integrating Sendmail and Mailman David Champion has contributed a recipe for more closely integrating Sendmail and Mailman, such that Sendmail will automatically recognize and deliver to new mailing lists as they are created, without having to manually edit alias tables. In the contrib directory of Mailman's source distribution, you will find four files: * mm-handler.readme - an explanation of how to set everything up * mm-handler - the mail delivery agent (MDA) * mailman.mc - a toy configuration file sample * virtusertable - a sample for RFC 2142 address exceptions 6.3.3 Performance notes One of the surest performance killers for Sendmail users is when Sendmail is configured to synchronously verify the recipient's host via DNS. If it does this for messages posted to it from Mailman, you will get horrible performance. Since Mailman usually connects via localhost (i.e. 127.0.0.1) to the SMTP port of Sendmail, you should be sure to configure Sendmail to not do DNS verification synchronously for localhost connections. 6.4 Using the Qmail mail server There are some issues that users of the qmail mail transport agent have encountered. None of the core maintainers use qmail, so all of this information has been contributed by the Mailman user community, especially Martin Preishuber and Christian Tismer, with notes by Balazs Nagy (BN) and Norbert Bollow (NB). * You might need to set the mail-gid user to either qmail, mailman, or nofiles by using the --with-mail-gid configure option. BN: it highly depends on your mail storing policy. For example if you use the simple ~alias/.qmail-* files, you can use `id -g alias`. But if you use /var/qmail/users, the specified mail gid can be used. If you are going to be directing virtual domains directly to the mailman user (using ``virtualdomains'' on a list-only domain, for example), you will have to use --with-mail-gid=gid of mailman user's group. This is incompatible with having list aliases in ~alias, unless that alias simply forwards to mailman-listname*. * If there is a user mailman on your system, the alias mailman-owner will work only in ~mailman. You have to do a touch .qmail-owner in ~mailman directory to create this alias. NB: An alternative, IMHO better solution is to chown root ~mailman, that will stop qmail from considering mailman to be a user to whom mail can be delivered. (See ``man 8 qmail-getpw''.) * In a related issue, if you have any users with the same name as one of your mailing lists, you will have problems if list names contain "-" in them. Putting .qmail redirections into the user's home directory doesn't work because the Mailman wrappers will not get spawned with the proper GID. The solution is to put the following lines in the /var/qmail/users/assign file: +zope-:alias:112:11:/var/qmail/alias:-:zope-: . where in this case the listname is e.g. zope-users. NB: Alternatively, you could host the lists on a virtual domain, and use the /var/qmail/control/virtualdomains file to put the mailman user in charge of this virtual domain. * BN:If inbound messages are delivered by another user than mailman, it's necessary to allow it to access ~mailman. Be sure that ~mailman has group writing access and setgid bit is set. Then put the delivering user to mailman group, and you can deny access to ~mailman to others. Be sure that you can do the same with the WWW service. By the way the best thing is to make a virtual mail server to handle all of the mail. NB: E.g. make an additional "A" DNS record for the virtual mailserver pointing to your IP address, add the line lists.kva.hu:mailman to /var/qmail/control/virtualdomains and a lists.kva.hu line to /var/qmail/control/rcpthosts file. Don't forget to HUP the qmail-send after modifying ``virtualdomains''. Then every mail to lists.kva.hu will arrive to mail.kva.hu's mailman user. Then make your aliases: .qmail => mailman@...'s letters .qmail-owner => mailman-owner's letters For list aliases, you can either create them manually: .qmail-list => posts to the 'list' list .qmail-list-admin => posts to the 'list's owner .qmail-list-request => requests to 'list' etc or for automatic list alias handling (when using the lists.kva.hu virtual as above), see contrib/qmail-to-mailman.py in the Mailman source distribution. Modify the ~mailman/.qmail-default to include: |preline /path/to/python /path/to/qmail-to-mailman.py and new lists will automatically be picked up. * You have to make sure that the localhost can relay. If you start qmail via inetd and tcpenv, you need some line the following in your /etc/hosts.allow file: tcp-env: 127. 10.205.200. : setenv RELAYCLIENT where 10.205.200. is your IP address block. If you use tcpserver, then you need something like the following in your /etc/tcp.smtp file: 10.205.200.:allow,RELAYCLIENT="" 127.:allow,RELAYCLIENT="" * BN: Bigger /var/qmail/control/concurrencyremote values work better sending outbound messages, within reason. Unless you know your system can handle it (many if not most cannot) this should not be set to a value greater than 120. * More information about setting up qmail and relaying can be found in the qmail documentation. BN: Last but not least, here's a little script to generate aliases to your lists (if for some reason you can/will not have them automatically picked up using contrib/qmail-to-mailman.py): This script is for the Mailman 2.0 series: #!/bin/sh if [ $# = 1 ]; then i=$1 echo Making links to $i in the current directory... echo "|preline /home/mailman/mail/mailman post $i" > .qmail-$i echo "|preline /home/mailman/mail/mailman mailowner $i" > .qmail-$i-admin echo "|preline /home/mailman/mail/mailman mailowner $i" > .qmail-$i-owner echo "|preline /home/mailman/mail/mailman mailowner $i" > .qmail-owner-$i echo "|preline /home/mailman/mail/mailman mailcmd $i" > .qmail-$i-request fi Note: This is for a new Mailman 2.1 installation. Users upgrading from Mailman 2.0 would most likely change /usr/local/mailman to /home/mailman. If in doubt, refer to the --prefix option passed to configure during compile time. #!/bin/sh if [ $# = 1 ]; then i=$1 echo Making links to $i in the current directory... echo "|preline /usr/local/mailman/mail/mailman post $i" > .qmail-$i echo "|preline /usr/local/mailman/mail/mailman admin $i" > .qmail-$i-admin echo "|preline /usr/local/mailman/mail/mailman bounces $i" > .qmail-$i-bounc es # The following line is for VERP # echo "|preline /usr/local/mailman/mail/mailman bounces $i" > .qmail-$i-bou nces-default echo "|preline /usr/local/mailman/mail/mailman confirm $i" > .qmail-$i-confi rm echo "|preline /usr/local/mailman/mail/mailman join $i" > .qmail-$i-join echo "|preline /usr/local/mailman/mail/mailman leave $i" > .qmail-$i-leave echo "|preline /usr/local/mailman/mail/mailman owner $i" > .qmail-$i-owner echo "|preline /usr/local/mailman/mail/mailman request $i" > .qmail-$i-reque st echo "|preline /usr/local/mailman/mail/mailman subscribe $i" > .qmail-$i-sub scribe echo "|preline /usr/local/mailman/mail/mailman unsubscribe $i" > .qmail-$i-u nsubscribe fi 6.4.1 Information on VERP You will note in the alias generating script for 2.1 above, there is a line for VERP that has been commented out. If you are interested in VERP there are two options. The first option is to allow Mailman to do the VERP formatting. To activate this, uncomment that line and add the following lines to your mm_cfg.py file: VERP_FORMAT = '%(bounces)s-+%(mailbox)s=%(host)s' VERP_REGEXP = r'^(?P.*?)-\+(?P[^=]+)=(?P[^@]+)@.*$' The second option is a patch on SourceForge located at: http://sourceforge.net/tracker/?func=detail&atid=300103&aid=645513&grou p_id=103 This patch currently needs more testing and might best be suitable for developers or people well familiar with qmail. Having said that, this patch is the more qmail-friendly approach resulting in large performance gains. 6.4.2 Virtual mail server As mentioned in the 6.4 section for a virtual mail server, a patch under testing is located at: http://sf.net/tracker/index.php?func=detail&aid=621257&group_id=103&ati d=300103 Again, this patch is for people familiar with their qmail installation. 6.4.3 More information You might be interested in some information on modifying footers that Norbert Bollow has written about Mailman and qmail, available here: http://mailman.cis.to/qmail-verh/ 7 Review your site defaults Mailman has a large number of site-wide configuration options which you should now review and change according to your needs. Some of the options control how Mailman interacts with your environment, and other options select defaults for newly created lists^5. There are system tuning parameters and integration options. The full set of site-wide defaults lives in the $prefix/Mailman/Defaults.py file, however you should never modify this file! Instead, change the mm_cfg.py file in that same directory. You only need to add values to mm_cfg.py that are different than the defaults in Defaults.py, and future Mailman upgrades are guaranteed never to touch your mm_cfg.py file. The Defaults.py file is documented extensively, so the options are not described here. The Defaults.py and mm_cfg.py are both Python files so valid Python syntax must be maintained or your Mailman installation will break. You should make any changes to mm_cfg.py using the account you installed Mailman under in the 3 section. 8 Create a site-wide mailing list After you have completed the integration of Mailman and your mail server, you need to create a ``site-wide'' mailing list. This is the one that password reminders will appear to come from, and it is required for proper Mailman operation. Usually this should be a list called mailman, but if you need to change this, be sure to change the MAILMAN_SITE_LIST variable in mm_cfg.py. You can create the site list with this command, following the prompts: % bin/newlist mailman Now configure your site list. There is a convenient template for a generic site list in the installation directory, under data/sitelist.cfg which can help you with this. You should review the configuration options in the template, but note that any options not named in the sitelist.cfg file won't be changed. The template can be applied to your site list by running: % bin/config_list -i data/sitelist.cfg mailman After applying the sitelist.cfg options, be sure you review the site list's configuration via the admin pages. You should also subscribe yourself to the site list. 9 Set up cron Several Mailman features occur on a regular schedule, so you must set up cron to run the right programs at the right time^6. If your version of crontab supports the -u option, you must be root to do this next step. Add $prefix/cron/crontab.in as a crontab entry by executing these commands: % cd $prefix/cron % crontab -u mailman crontab.in If you used the --with-username option, use that user name instead of mailman for the -u argument value. If your crontab does not support the -u option, try these commands: % cd $prefix/cron % su - mailman % crontab crontab.in Warning: If you accepted the defaults for the --with-username option and for the name of the site list, and one of the cron jobs ever encounters an error, the cron daemon will mail the error output to the 'mailman' user and it will most likely be delivered to the 'mailman' site list and possibly not be accepted. For this reason it is a good idea to insert MAILTO=user@example.com or MAILTO=mailman-owner at the beginning of crontab.in before installing it to cause this output to be mailed to a real user or to the owner of the site list or to configure the site list (see section 8) to accept this mail. 10 Start the Mailman qrunner Mailman depends on a process called the ``qrunner'' to delivery all email messages it sees. You must start the qrunner by executing the following command from the $prefix directory: % bin/mailmanctl start You probably want to start Mailman every time you reboot your system. Exactly how to do this depends on your operating system. If your OS supports the chkconfig command (e.g. RedHat and Mandrake Linuxes) you can do the following (as root, from the Mailman install directory): % cp misc/mailman /etc/init.d/mailman % chkconfig --add mailman Note that /etc/init.d may be /etc/rc.d/init.d on some systems. On Gentoo Linux, you can do the following: % cp misc/mailman /etc/init.d/mailman % rc-update add mailman default On Debian, you probably want to use: % update-rc.d mailman defaults For Unixes that don't support chkconfig, you might try the following set of commands: % cp misc/mailman /etc/init.d/mailman % cd /etc/rc.d/rc0.d % ln -s ../init.d/mailman K12mailman % cd ../rc1.d % ln -s ../init.d/mailman K12mailman % cd ../rc2.d % ln -s ../init.d/mailman S98mailman % cd ../rc3.d % ln -s ../init.d/mailman S98mailman % cd ../rc4.d % ln -s ../init.d/mailman S98mailman % cd ../rc5.d % ln -s ../init.d/mailman S98mailman % cd ../rc6.d % ln -s ../init.d/mailman K12mailman 11 Check the hostname settings You should check the values for DEFAULT_EMAIL_HOST and DEFAULT_URL_HOST in Defaults.py. Make any necessary changes in the mm_cfg.py file, not in the Defaults.py file. If you change either of these two values, you'll want to add the following afterwards in the mm_cfg.py file: add_virtualhost(DEFAULT_URL_HOST, DEFAULT_EMAIL_HOST) You will want to run the bin/fix_url.py to change the domain of any existing lists. 12 Create the site password There are two site-wide passwords that you can create from the command line, using the bin/mmsitepass script. The first is the ``site password'' which can be used anywhere a password is required in the system. The site password will get you into the administration page for any list, and it can be used to log in as any user. Think root for a Unix system, so pick this password wisely! The second password is a site-wide ``list creator'' password. You can use this to delegate the ability to create new mailing lists without providing all the privileges of the site password. Of course, the owner of the site password can also create new mailing lists, but the list creator password is limited to just that special role. To set the site password, use this command: % $prefix/bin/mmsitepass To set the list creator password, use this command: % $prefix/bin/mmsitepass -c It is okay not to set a list creator password, but you probably do want a site password. 13 Create your first mailing list For more detailed information about using Mailman, including creating and configuring mailing lists, see the Mailman List Adminstration Manual. These instructions provide a quick guide to creating your first mailing list via the web interface: * Start by visiting the url http://my.dom.ain/mailman/create. * Fill out the form as described in the on-screen instructions, and in the ``List creator's password'' field, type the password you entered in section 7. Type your own email address for the ``Initial list owner address'', and select ``Yes'' to notify the list administrator. * Click on the ``Create List'' button. * Check your email for a message from Mailman informing you that your new mailing list was created. * Now visit the list's administration page, either by following the link on the confirmation web page or clicking on the link from the email Mailman just sent you. Typically the url will be something like http://my.dom.ain/mailman/admin/mylist. * Type in the list's password and click on ``Let me in...'' * Click on ``Membership Management'' and then on ``Mass Subscription''. * Enter your email address in the big text field, and click on ``Submit Your Changes''. * Now go to your email and send a message to mylist@my.dom.ain. Within a minute or two you should see your message reflected back to you via Mailman. Congratulations! You've just set up and tested your first Mailman mailing list. If you had any problems along the way, please see the 14 section. 14 Troubleshooting If you encounter problems with running Mailman, first check the question and answer section below. If your problem is not covered there, check the online help, including the FAQ and the community FAQ wiki. Also check for errors in your syslog files, your mail and web server log files and in Mailman's $prefix/logs/error file. If you're still having problems, you should send a message to the mailman-users@python.org mailing list^7; see http://mail.python.org/mailman/listinfo/mailman-users for more information. Be sure to including information on your operating system, which version of Python you're using, and which version of Mailman you're installing. Here is a list of some common questions and answers: * Problem: All Mailman web pages give a 404 File not found error. Solution: Your web server has not been set up properly for handling Mailman's CGI programs. Make sure you have: 1. configured the web server to give permissions to $prefix/cgi-bin 2. restarted the web server properly. Consult your web server's documentation for instructions on how to do check these issues. * Problem: All Mailman web pages give an "Internal Server Error". Solution: The likely problem is that you are using the wrong user or group for the CGI scripts. Check your web server's log files. If you see a line like Attempt to exec script with invalid gid 51, expected 99 you will need to reinstall Mailman, specifying the proper CGI group id, as described in the 3 section. * Problem: I send mail to the list, and get back mail saying the list is not found! Solution: You probably didn't add the necessary aliases to the system alias database, or you didn't properly integrate Mailman with your mail server. Perhaps you didn't update the alias database, or your system requires you to run newaliases explicitly. Refer to your server specific instructions in the 6 section. * Problem: I send mail to the list, and get back mail saying, ``unknown mailer error''. Solution: The likely problem is that you are using the wrong user or group id for the mail wrappers. Check your mail server's log files; if you see a line like Attempt to exec script with invalid gid 51, expected 99 you will need to reinstall Mailman, specifying the proper mail group id as described in the 3 section. * Problem: I use Postfix as my mail server and the mail wrapper programs are logging complaints about the wrong GID. Solution: Make sure the $prefix/data/aliases.db file is user owned by mailman (or whatever user name you used in the configure command). If this file is not user owned by mailman, Postfix will not run the mail programs as the correct user. * Problem: I use Sendmail as my mail server, and when I send mail to the list, I get back mail saying, ``sh: mailman not available for sendmail programs''. Solution: Your system uses the Sendmail restricted shell (smrsh). You need to configure smrsh by creating a symbolic link from the mail wrapper ($prefix/mail/mailman) to the directory identifying executables allowed to run under smrsh. Some common names for this directory are /var/admin/sm.bin, /usr/admin/sm.bin or /etc/smrsh. Note that on Debian Linux, the system makes /usr/lib/sm.bin, which is wrong, you will need to create the directory /usr/admin/sm.bin and add the link there. Note further any aliases newaliases spits out will need to be adjusted to point to the secure link to the wrapper. * Problem: I messed up when I called configure. How do I clean things up and re-install? Solution: % make clean % ./configure --with-the-right-options % make install 15 Platform and operating system notes Generally, Mailman runs on any POSIX-based system, such as Solaris, the various BSD variants, Linux systems, MacOSX, and other generic Unix systems. It doesn't run on Windows. For the most part, the generic instructions given in this document should be sufficient to get Mailman working on any supported platform. Some operating systems have additional recommended installation or configuration instructions. 15.1 GNU/Linux issues Linux seems to be the most popular platform for running Mailman. Here are some hints on getting Mailman to run on Linux: * If you are getting errors with hard link creations and/or you are using a special secure kernel (securelinux/openwall/grsecurity), see the file contrib/README.check_perms_grsecurity in the Mailman source distribution. Note that if you are using Linux Mandrake in secure mode, you are probably concerned by this. * Apparently Mandrake 9.0 changed the permissions on gcc, so if you build as the mailman user, you need to be sure mailman is in the cctools group. * If you installed Python from your Linux distribution's package manager (e.g. .rpms for Redhat-derived systems or .deb for Debian), you must install the ``development'' package of Python, or you may not get everything you need. For example, using Python 2.2 on Debian, you will need to install the python2.2-dev package. On Redhat, you probably need the python2-devel package. If you install Python from source, you should be fine. One symptom of this problem, although for unknown reasons, is that you might get an error such as this during your install: Traceback (most recent call last): File "bin/update", line 44, in ? import paths ImportError: No module named paths make: *** [update] Error 1 If this happens, install the Python development package and try configure and make install again. Or install the latest version of Python from source, available from http://www.python.org. This problem can manifest itself in other Linux distributions in different ways, although usually it appears as ImportErrors. 15.2 BSD issues Vivek Khera writes that some BSDs do nightly security scans for setuid file changes. setgid directories also come up on the scan when they change. Also, the setgid bit is not necessary on BSD systems because group ownership is automatically inherited on files created in directories. On other Unixes, this only happens when the directory has the setgid bit turned on. To install without turning on the setgid bit on directories, simply pass in the DIRSETGID variable to make, after you've run configure: % make DIRSETGID=: install This disables the chmod g+s command on installed directories. 15.3 MacOSX issues Much of the following is no longer applicable to more recent versions of MacOSX. See the FAQ at http://wiki.list.org/x/O4A9 for links to more recent information. Many people run Mailman on MacOSX. Here are some pointers that have been collected on getting Mailman to run on MacOSX. * Jaguar (MacOSX 10.2) comes with Python 2.2. While this isn't the very latest stable version of Python, it ought to be sufficient to run Mailman 2.1. * David B. O'Donnell has a web page describing his configuration of Mailman 2.0.13 and Postfix on MacOSX Server. http://www.afp548.com/Articles/mail/python-mailman.html * Kathleen Webb posted her experiences in getting Mailman running on Jaguar using Sendmail. http://mail.python.org/pipermail/mailman-users/2002-October/022944. html * Panther server (MacOSX 10.3) comes with Mailman; Your operating system should contain documentation that will help you, and Apple has a tech document about a problem you might encounter running Mailman on Mac OS X Server 10.3: http://docs.info.apple.com/article.html?artnum=107889 Terry Allen provides the following detailed instructions on running Mailman on the 'client' version of OSX, or in earlier versions of OSX: Mac OSX 10.3 and onwards has the basics for a successful Mailman installation. Users of earlier versions of Mac OSX contains Sendmail and those users should look at the Sendmail installation section for tips. You should follow the basic installation steps as described earlier in this manual, substituting as appropriate, the steps outlined in this section. By default, Mac OSX 10.3 'client' version does not have a fully functional version of Postfix. Setting up a working MTA such as Postfix is beyond the scope of this guide and you should refer to http://www.postfix.org for tips on getting Postfix running. An easy way to set Postfix up is to install and run Postfix Enabler, a stand-alone tool for configuring Postfix on Mac OSX, available from http://www.roadstead.com/weblog/Tutorials/PostfixEnabler.html. Likewise, Mac OSX 'client' version from 10.1 onwards includes a working Apache webserver. This is switched on using the System Preferences control panel under the 'Sharing tab'. A useful tool for configuring the Apache on Mac OSX is Webmin, which can be obtained from http://www.webmin.com. Webmin can also perform configuration for other system tasks, including Postfix, adding jobs to your crontab, adding user and groups, plus adding startup and shutdown jobs. In a stock installation of OSX, the requirement for Mailman is to have Python installed. Python is not installed by default, so it is advised that you install the developer's tools package, which may have been provided with your system. It can also be downloaded from the Apple developer site at http://connect.apple.com. Not only is the developer tools package an essential requirement for installing Mailman, but it will come in handy at a later date should you need other tools. The developer's tools are also know by the name XCode tools. As a minimum, the Python version should be 2.2, but 2.3 is recommended. If you wish to add a user and group using the command line in OSX instead of via Webmin or another GUI interface, open your terminal application and follow the commands as indicated below - do not type the comments following the "#" since they are just notes: sudo tcsh niutil -create / /users/mailman niutil -createprop / /users/mailman name mailman # Note that xxx is a free user ID number on your system niutil -createprop / /users/mailman uid xxx niutil -createprop / /users/mailman home /usr/local/mailman mkdir -p /usr/local/mailman niutil -createprop / /users/mailman shell /bin/tcsh passwd mailman # To prevent malicious hacking, supply a secure password here niutil -create / /groups/mailman niutil -createprop / /groups/mailman name mailman # Note that xxx is a free group ID number on your system niutil -createprop / /groups/mailman gid xxx niutil -createprop / /groups/mailman passwd '*' niutil -createprop / /groups/mailman users 'mailman' chown mailman:mailman /usr/local/mailman cd /usr/local/mailman chmod a+rx,g+ws . exit su mailman For setting up Apache on OSX to handle Mailman, the steps are almost identical and the configuration file on a stock Mac OSX Client version is stored in the nearly standard location of /etc/httpd/httpd.conf. The AFP548.com site has a time-saving automated startup item creator for Mailman, which can be found at http://www.afp548.com/Software/MailmanStartup.tar.gz To install it, copy it into your /Library/StartupItems directory. As the root or superuser, from the terminal, enter the following: gunzip MailmanStartup.tar.gz tar xvf MailmanStartup.tar It will create the startup item for you so that when you reboot, Mailman will start up. About this document ... GNU Mailman - Installation Manual, February 26, 2019, Release 2.1 This document was generated using the LaTeX2HTML translator. LaTeX2HTML is Copyright © 1993, 1994, 1995, 1996, 1997, Nikos Drakos, Computer Based Learning Unit, University of Leeds, and Copyright © 1997, 1998, Ross Moore, Mathematics Department, Macquarie University, Sydney. The application of LaTeX2HTML to the Python documentation has been heavily tailored by Fred L. Drake, Jr. Original navigation icons were contributed by Christopher Petrilli. __________________________________________________________________ Footnotes ... right^1 You will be able to check and repair your permissions after installation is complete. .../usr/local/mailman^2 This is the default for Mailman 2.1. Earlier versions of Mailman installed everything under /home/mailman by default. ... set^3 BSD users should see the 15.2 section for additional information. ... only^4 In fact, in later versions of Mailman, this module is explicitly sabotaged. You have to know what you're doing in order to re-enable it. ... lists^5 In general, changing the list defaults described in this section will not affect any already created lists. To make changes after a list has been created, use the web interface or the command line scripts, such as bin/withlist and bin/config_list. ... time^6 Note that if you're upgrading from a previous version of Mailman, you'll want to install the new crontab, but be careful if you're running multiple Mailman installations on your site! Changing the crontab could mess with other parallel Mailman installations. ... list^7 You must subscribe to this mailing list in order to post to it, but the mailing list's archives are publicly visible. __________________________________________________________________ Previous Page Up one Level Next Page GNU Mailman - Installation Manual __________________________________________________________________ Release 2.1, documentation updated on February 26, 2019.