If you want the recalculation of fields to happen automatically, or if you want to be able to assign names22 to fields and columns, you need to reserve the first column of the table for special marking characters.
org-table-rotate-recalc-marks) ¶Rotate the calculation mark in first column through the states ‘#’, ‘*’, ‘!’, ‘$’. When there is an active region, change all marks in the region.
Here is an example of a table that collects exam results of students and makes use of these features:
|---+---------+--------+--------+--------+-------+------| | | Student | Prob 1 | Prob 2 | Prob 3 | Total | Note | |---+---------+--------+--------+--------+-------+------| | ! | | P1 | P2 | P3 | Tot | | | # | Maximum | 10 | 15 | 25 | 50 | 10.0 | | ^ | | m1 | m2 | m3 | mt | | |---+---------+--------+--------+--------+-------+------| | # | Peter | 10 | 8 | 23 | 41 | 8.2 | | # | Sam | 2 | 4 | 3 | 9 | 1.8 | |---+---------+--------+--------+--------+-------+------| | | Average | | | | 25.0 | | | ^ | | | | | at | | | $ | max=50 | | | | | | |---+---------+--------+--------+--------+-------+------| #+TBLFM: $6=vsum($P1..$P3)::$7=10*$Tot/$max;%.1f::$at=vmean(@-II..@-I);%.1f
Important: Please note that for these special tables, recalculating the table with C-u C-c * only affects rows that are marked ‘#’ or ‘*’, and fields that have a formula assigned to the field itself. The column formulas are not applied in rows with empty first field.
The marking characters have the following meaning:
The fields in this line define names for the columns, so that you may refer to a column as ‘$Tot’ instead of ‘$6’.
This row defines names for the fields above the row. With such a definition, any formula in the table may use ‘$m1’ to refer to the value ‘10’. Also, if you assign a formula to a names field, it is stored as ‘$name = ...’.
Similar to ‘^’, but defines names for the fields in the row below.
Fields in this row can define parameters for formulas. For example, if a field in a ‘$’ row contains ‘max=50’, then formulas in this table can refer to the value 50 using ‘$max’. Parameters work exactly like constants, only that they can be defined on a per-table basis.
Fields in this row are automatically recalculated when pressing TAB or RET or S-TAB in this row. Also, this row is selected for a global recalculation with C-u C-c *. Unmarked lines are left alone by this command.
Selects this line for global recalculation with C-u C-c *, but not for automatic recalculation. Use this when automatic recalculation slows down editing too much.
Do not export this line. Useful for lines that contain the narrowing ‘<N>’ markers or column group markers.
Finally, just to whet your appetite for what can be done with the fantastic Calc package, here is a table that computes the Taylor series of degree n at location x for a couple of functions.
|---+-------------+---+-----+--------------------------------------| | | Func | n | x | Result | |---+-------------+---+-----+--------------------------------------| | # | exp(x) | 1 | x | 1 + x | | # | exp(x) | 2 | x | 1 + x + x^2 / 2 | | # | exp(x) | 3 | x | 1 + x + x^2 / 2 + x^3 / 6 | | # | x^2+sqrt(x) | 2 | x=0 | x*(0.5 / 0) + x^2 (2 - 0.25 / 0) / 2 | | # | x^2+sqrt(x) | 2 | x=1 | 2 + 2.5 x - 2.5 + 0.875 (x - 1)^2 | | * | tan(x) | 3 | x | 0.0175 x + 1.77e-6 x^3 | |---+-------------+---+-----+--------------------------------------| #+TBLFM: $5=taylor($2,$4,$3);n3
Such names must start with an alphabetic character and use only alphanumeric/underscore characters.